FOR SALE

[bbanna]

This time I made a list of everything. If you are interested or you know someone who may be interested. Her eit all is.

FOR SALE: 1989 Honda CB-1
STATUS: completely disassembled for rebuild project
$3500.00 + shipping
This bike was purchased with the intention of a rebuild project. It is currently disassembled. All parts are stored in boxes. To finish and reassemble the bike, there are only two parts that need to be purchased and one part that needs to be fabricated. These parts are a new front brake rotor, new rear brake rotor and an exhaust hanger bracket. The old rotors are stored in boxes with all the other parts. Below is a list of all the parts from the original bike plus all the parts I have purchased for this project plus parts that were not intended for the project that I purchased because the price was too good to pass up and could be used on a second rebuild project.

I will NOT part the bike out!

Package includes everything the bike had when I originally purchased it, except for Kerker exhaust, plus the following:

FRAME:
-   Motor mounts gusseted.
-   Brake hanger bracket removed and mounting tabs for a removable one installed.
-   Side stand bracket rebuilt to be removable for track days.
-   Center stand bracket removed and ground off.
-   Sand blasted and powder coated black satin.

FRONT END:
-   CBR929RR forks. Forks have been rebuilt by Lindeman Engineering. They are setup for 200 lbs. Forks are in EXCELLENT condition.
-   CBR929RR triple tree. Rebuilt with tabs to mount CB-1 clocks. Powder coated black.
-   CBR929RR brake NISSIN brake calipers. Needs to be rebuilt and cleaned.
-   CBR929RR front fender (red)
-   New CBR929RR clip-ons.
-   CRG brake and cluck levers.
-   Clock case painted red
-   Brand new clock cover, indicator light covers and seal.
-   ALL BALLS taper bearing head set and new races.
-   New head castle nuts and seals.
-   Honda MAGTEK magnesium wheel. Powder coated black. Setup for single brake rotor. Brand new bearings (need to be installed).
-   Ti bolt sets for all front end parts.

MOTOR:
-   New (used) oil pan.
-   Custom made aluminum left side case cover (total of 3).
-   BEET Japan right side heavy case cover.
-   New OEM right side case cover.
-   New (never used) Keihin 32mm Flat Slide carburetors with velocity stacks.
-   Spare radiator with side covers.
-   Spare coils and spark plug wires.
-   Two CB-1 black boxes
-   Spare complete wiring harness.
-   Yoshimura full Ti exhaust system. From Honda CB400SF.
-   New CBR400RR dual exhaust system, pipes come up either side of bike. Head pipes need modification to clear bottom of oil pan.
-   15 tooth counter shaft sprocket.
-   All new OEM gaskets and seals to rebuild engine. All still in OEM packages.

REAR END:
-   CBR400RR Gull swing arm. All modification made to fit CB-1 frame which include custom made frame spacers and shock mount. Swing arm is polished and chromed.
-   New Penske remote reservoir adjustable height shock. Set up for 200 lbs.
-   Inner hugger painted red.
-   New OEM chain guard and chain slider for CBR400RR swing arm
-   Honda MAGTEK magnesium wheel. Powder coated black. New OEM rubber cush drive parts and bearings (need to be installed).
-   Rear swing arm stand buttons.
-   Brake hanger polished.
-   Spare sets of axles and spacers.
-   CBR400RR brake calipers (needs to be cleaned and refurbished).

MISCELANIOUS:
-   Fender eliminator kit.
-   MC28 single sided swing arm.
-   MC28 MAGTEK magnesium wheels.
-   CBR250R swing arm with shock.
-   CBR600F2 front end (forks, fender, brakes).
-   CBR600F2 front wheel with Michelin Pilot tire. Barely 500 miles on tire
-   CBR600F2 rear wheel setup to fit CB-1 with Michelin Pilot tire. Barely 500 miles on tire.
-   Extra set of Honda MAGTEK magnesium wheels (18” rear wheel) from MC18.
-   Extra brake handles.
-   Aftermarket foot pegs.
-   BEET Japan rear sets for CB-1 (does not come with foot pegs).
-   New Keihin 28mm round slide carburetors.
-   Pit Bull swing arm stand
-   Pit Bull front end stand. Both under forks and steering tube lift.
-   Engine/frame sliders.

[CB1 in SF]

That's a lot of nice bits.  Good luck with your sale 

Whoever buys this, I'll take the CBR F2 wheels off yer hands to help defray the costs of the package.

[bbanna]

I forgot to add these items as well.

-   CB-1 Owners/ Service manual.
-   VFR400R (NC30) parts manual.
-   RVF400R (NC35) parts manual.
-   CBR400RR (various models) parts manual.

[ptlcb1]

I hope its all still available in the Spring of next year!  (fingers crossed until then!)

[stussels]

these lists are great and all but we really need some pics of all this creamy goodness. 

[bbanna]

It is all packed away in boxes. It would take way to much time for me to spread it all out to take photos. I am to lazy to do that and have other things that I want to do.

If I did do that, I would probably start workingon it again .

Brian

[ptlcb1]

Keep it in the boxes.  I wouldnt want anyone to be tempted to buy my stuff! 

[bbanna]

Pete,

I do not think there is any threat of that. I have no desire to start digging into it all. It is all in a nice dry safe spot in my garage. I even keep the spiders away with weekly garage cleanings  .

Brian